Iscsi on sigtar.com

solaris - storage server

Mon, 11 Jul 2011 00:00:00 +1200

http://p2v.it/2010/04/15/a-next-generation-multiprotocol-storage-for-your-homelab-on-a-budget-part-1/

Setup iSCSI target using comstar – pkg install -v storage-server pkg install pkg:/SUNWiscsit svcadm enable stmf svcadm enable svc:/network/iscsi/target:default itadm create-target reboot – -r

Create the iSCSI store — zfs create -V 100G DataPool/TestDatastore1 sbdadm create-lu /dev/zvol/rdsk/DataPool/TestDatastore1 stmfadm create-hg ESX4-group stmfadm add-hg-member -g ESX4-group wwn.2100001b329711bd wwn.2101001b32b711bd stmfadm add-view -h ESX4-group -n 0 600144F03EBEC50000004BA86E460001 stmfadm list-lu -v

P4000 / Lefthand and Windows DSM (MPIO)

Wed, 04 May 2011 00:00:00 +1200

Steps to setup MPIO round robin and DSM with P4000 / Lefthand nodes

This example is windows 2008 with 2 x 1gbit nics

Install HP DSM driver onto windows 2008 (this should also install MPIO feature on windows 2008)
Setup 2 x IP’s on windows host - storage subnet (used with MPIO)
1. Confirm you can ping target from both (enable one at a time - ensure there is no routing on your other nics)
Provision storage and allow server read / write access to windows server (via initiator name)
Open iSCSI on windows 2008
Put in IP of target in discovery tab
On first tab confirm that iSCSI drive is presented to host
Click “connect” - check both auto-connect and use MPIO
1. click advanced - chose MS iSCSI initiator, choose first IP and target IP. Click o.k. / o.k
2. click advanced - chose MS iSCSI initiator, choose second IP and target IP. Click o.k. / o.k
3. Repeat above per additional Nic
Confirm via “devices” that there is x (as many targets as nics) targets per disk
1. Within devices choose MPIO - change from vendor specific to “round robin”
  1. Note : read / write access to LUN is required when using “round robin” MPIO opposed to the default “vendor specific” which works with read only access. Else you will get an error - “not supported”
2. Repeat above per “device”
Confirm on Lefthand / P4000 CMC that the LUN has one connection per initiator Nic, and that each connection also has its DSM children (visible in CMC if working).

Confirm that the connection are as expected…

vmware - measuring iscsi write performance

Fri, 07 May 2010 00:00:00 +1200

I picked this trick up off vmware support. If you’ve got your iscsi all setup you can drop to the shell (either ssh or console) and do this to measure your average write throughput.

time vmkfstools -c 10G /vmfs/volumes/san_vmfs/my_vm/fat_disk.vmdk -d eagerzeroedthick

Try larger a larger disk if this is too quick (free space permitting)

Essentially this will initiate the host to create a fat disk in the location above. You will then get a time recorded on how long it takes to execute this command. Then you can use your maths skill to work out the transfer rate…

vSphere and Multipathing iSCSI

Thu, 04 Feb 2010 00:00:00 +1300

This is just a quick reference to create a multiplathing iSCSI setup…

Create two virtual kernel switches, one called “iSCSI-1” and the other called “iSCSI-2” (and so on if you have more nics)

Then per kernel portgroup ensure that only one of the nics is active. For the “iSCSI-1” portgroup configure it to override the virtual switch settings and move nic 0 to active and nic 1 to unused. For the “iSCSI-2” portgroup configure it to override the virtual switch settings and move nic 1 to active and nic 0 to unused.

OpenSolaris - iSCSI

Fri, 13 Nov 2009 00:00:00 +1300

Want iSCSI in opensolaris?

Grab SUNWiscsitgt via package manager.

enable the server via svcadm;

svcadm enable iscsitgt

create your zfs iscsi pool; (this command will limit iscsi drive to 500GB in size)

zfs create -V 500G tank/iscsi

set isci on via zfs command;

zfs set shareiscsi=on tank/iscsi

check that target is up and running;

iscsitadm list target -v

Done. Should be able to connect via ip from another machine. I have not covered CHAP or any client side configuration. Assumed isolated LAN.

ESX - network utilization

Sat, 22 Aug 2009 00:00:00 +1200

One of the best articles i have found on this subject is here : http://blog.scottlowe.org/2008/07/16/understanding-nic-utilization-in-vmware-esx/

There is some additional information here on setting up an etherchannel on the cisco side : http://blog.scottlowe.org/2006/12/04/esx-server-nic-teaming-and-vlan-trunking/

This can be handy if you need a single VM to use both physical nics in a load-balanced manner - both outbound and inbound. Of course its not really that simple though. This will really only add a benefit if the VM is communicating to multiple destinations (using ip hash - a single destination from a single VM with one IP will always be limited to the same physical nic).