Mpio

Steps to setup MPIO round robin and DSM with P4000 / Lefthand nodes

This example is windows 2008 with 2 x 1gbit nics

1. Install HP DSM driver onto windows 2008  (this should also install MPIO feature on windows 2008)
2. Setup 2 x IP’s on windows host - storage subnet (used with MPIO)
   1. Confirm you can ping target from both (enable one at a time - ensure there is no routing on your other nics)
3. Provision storage and allow server read / write access to windows server (via initiator name)
4. Open iSCSI on windows 2008
5. Put in IP of target in discovery tab
6. On first tab confirm that iSCSI drive is presented to host
7. Click “connect” - check both auto-connect and use MPIO
   1. click advanced - chose MS iSCSI initiator, choose first IP and target IP. Click o.k. / o.k
   2. click advanced - chose MS iSCSI initiator, choose second IP and target IP. Click o.k. / o.k
   3. Repeat above per additional Nic
8. Confirm via “devices” that there is x (as many targets as nics) targets per disk
   1. Within devices choose MPIO - change from vendor specific to “round robin”
      1. Note : read / write access to LUN is required when using “round robin” MPIO opposed to the default “vendor specific” which works with read only access. Else you will get an error - “not supported”
   2. Repeat above per “device”
9. Confirm on Lefthand / P4000 CMC that the LUN has one connection per initiator Nic, and that each connection also has its DSM children (visible in CMC if working).

Confirm that the connection are as expected…

Straight from the post below, this is the best way (currently) to load balance your NFS datastores…  No MPIO magic here unfortunately.

http://communities.vmware.com/message/1466595#1466595

Basically you can setup IP alias on the NFS side and then setup multiple connections (using a unique IP) per datastore  on each ESX host. This works well if you are using a team of nics running IP-hash load balancing…

Static EtherChannel.

My setup is as follows:

ESXi 4.0 U1, Cisco 3750 Switches, and NetApp NFS on the storage side.

I have a total of 8 nics. I divided the nics into 3 groups.

2 nics on vSwitch0 for Mgmt & vMotion 3 nics on vSwitch1 for VM’s (Multiple port groups (3 VLANS)) 3 nics on vSwitch2 for IP Storage (Mostly NFS, a little iSCSI) (One vSwitch3 I also have a VM port group for iSCSI access from within the VM)

Since I have 3 nics on my IPStorage port group I needed a way to be able to utilize all three nics and not have the server just use one for ingress and egress traffic. This was done by:

Setting up a static EtherChannel on the cisco switch (Port Channel). Configuring the cisco switch to IP Hash Configure the vSwitch to “Route based on IP Hash” as well.

The next part is to create multiple datastores on the NFS device. Each of my NFS datastores is about 500GB in size. Reason for this is that my larger luns are iSCSI and are access directly from the VM using the MS iSCSI initiator from the VM itself. My NetApp NAS has an address of, let say, 192.168.1.50. So all my data stores are accessible by utilizing the address of “\\192.168.1.50\NFS-Store#”. This will not be useful as the esx box and the cisco switch will always use the same nic/port to access the nas device. This is due to the algorithm (IP HASH) to decide what link it’ll go over. So to resolve the issue, I added IP aliases to the NFS box. NetApp allows to have multiple Ip addresses pointing to the same NFS export, I suspect EMC would do the same. So, I added 2 aliases 51 & 52. Now my NFS datastores are accessible by using Ip address 192.168.1.50,.51, & .52.

So I went ahead and added the datastores to the ESX box using the multiple IP addresses:

Datastore1 = \\192.168.1.50\NFS-Store1 Datastore2 = \\192.168.1.51\NFS-Store2 Datastore3 = \\192.168.1.52\NFS-Store3

If you have more datastores it’ll just repeat: Datastore4 = \\192.168.1.50\NFS-Store4 and so on…

Since having multiple datastores and address to each, the 3 nics on the ESX box dedicated to IP Storage get utilized. It does not aggregate the bandwidth but it does use all three to send and recieve packets. So the fastest speed you will get is 1Gbit, theoretically, each way for traffic but, it is better than trying to cram all the traffic over 1 nic.

I also enabled Jumbo Frames on the vSwitch as well as the vmNic for IP-Stroage. (need the best performance!) I should mention that your NFS storage device should have EtherChannel setup on it as well. Otherwise, you’ll be on the same boat just on the other end of it.

Hope it helps!

Larry B.

I should mention that you should not use different addresses to access the same NFS share (datastore). It is not supported and may cause you issues.

This is just a quick reference to create a multiplathing iSCSI setup…

Create two virtual kernel switches, one called “iSCSI-1” and the other called “iSCSI-2” (and so on if you have more nics)

Then per kernel portgroup ensure that only one of the nics is active. For the “iSCSI-1” portgroup configure it to override the virtual switch settings and move nic 0 to active and nic 1 to unused. For the “iSCSI-2” portgroup configure it to override the virtual switch settings and move nic 1 to active and nic 0 to unused.